电缆桥架一次成型设备

江阴市博士杰科技有限公司是最专业的制造电缆桥架一次成型设备的江苏地区最好的供应商

联系人：汤灵珠  联系电话：13906181752

电缆桥架设备

1.技术标准

1.1 CECS31:2006     《钢制电缆桥架工程设计规范》

1.2 GB/T6725-2002   《冷弯型钢技术条件》

1.3 GB/T6728-200    《结构用冷弯空心型钢尺寸、外型、重量及允许偏差》

1.4 GB6723-86       《通用冷弯开口型钢尺寸、外形、重量及允许偏差》

1.5 GB/709-88       《热轧钢板和钢带的尺寸、外形、重量及允许偏差》

1.6 GB/708-88       《冷轧钢板和钢带的尺寸、外形、重量及允许偏差》

2.设备技术要求

2.1设备技术条件：

2.1.1设备占地面积： 45×3.5×5（长×宽×高）米。

2.1.2设备进料方向：左进右出(待定)。

2.1.3电压参数380，50Hz，3相。

2.1.4气源：流量为0.5m³/分钟；压力为0-0.6MPa。

2.1.5液压油：46#液压油。

2.1.6齿轮油：18#双曲线齿轮油。

2.1.7设备颜色：蓝色为主，传动部位及防护盖等采用红色或黄色等警示色调

2.1.8产品尺寸及冲筋（开模）以双方签字确认的图为准。

3. 设备主要技术参数

3.2.1轧制带钢宽度：200—1050 mm

3.2.2轧制带钢厚度：0.7~2.0 mm

 3.2.3 轧制带钢材质：Q235冷轧带钢

3.2.4在线冲孔、生产速度：2-4m/分钟

3.2.5轧制工件长度：2000—6000 mm

3.2.6电机防爆等级ExfIICT4

3.2.7电机防护等级IP55

 3.2.8设备装机总容量：约73KW。

 1. The technical standards
1.1 CECS31:2006 specification for design of steel cable bridge engineering
1.2 GB/T6725-2002 "the cold bending steel technical conditions"
1.3 GB/T6728-200 "structure with cold bending hollow section size, shape, weight and allowable deviation"
1.4 GB6723-86 "general opening cold bend steel size, shape, weight and allowable deviation"
1.5 GB / 709-709 "hot rolled steel plate and steel belt of the size, shape, weight and allowable deviation"
1.6 GB / 708-708 "cold rolled steel plate and steel belt of size, shape, weight and allowable deviation"
2. The equipment technical requirements
2.1 equipment technical conditions:
2.1.1 equipment area: 45 * 3.5 * 5 meters (length x width x height).
2.1.2 equipment feed direction: left to right (pending).
2.1.3 voltage parameters for 380, 50 Hz, 3 phase.
2.1.4 gas source: flow of 0.
2.1.5 hydraulic oil: 46 # hydraulic oil.
2.1.6 gear oil: 18 # hyperbolic gear oil.
2.1.7 device color: blue is given priority to, transmission parts and protective cover, such as red or yellow warning tone
2.1.8 product size and screed (mould) with figure of confirmation signed by both sides.
3. The main technical parameters of the equipment
3.2.1 rolling strip width: 200-1050 mm
3.2.2 rolling strip steel thickness: 0.7 ~ 2.0 mm
3.2.3 rolling steel strip material: Q235 cold-rolled strip steel
3.2.4 online punching and production speed: 2-4 m/min
3.2.5 rolling workpiece length: 2000-6000 mm
3.2.6 ExfIICT4 explosion-proof motor level
3.2.7 motors IP55 protection level
3.2.8 equipment installed gross capacity: 73 kw.
5 m3 / min; Pressure to 0-0.6 MPa.